milifront.blogg.se

1. ATC SUBWOOFER HOW TO
2. ATC SUBWOOFER DRIVERS
3. ATC SUBWOOFER DRIVER
4. ATC SUBWOOFER PRO
5. ATC SUBWOOFER PROFESSIONAL

One of the most important issues in loudspeaker design is to determine the maximum countinuous spl level required. To purchase C1 Sub spares or accessories, please contact the company via their website or visit an. AW-7 is passive, it must be placed near the wall in the room. This website is not affiliated with or sponsored by ATC. AINOgradient has dsp and this measured response is straight down to 30Hz in the room. In the attached graphics there is a 6½" vs 10" sealed bass speakers in same outdoor measurement session.

ATC SUBWOOFER DRIVERS

Doubling bass drivers is a good choice but the volume of the cabinet should be doubled too. This is mainly of concern in small 5-6½"monitors already below 200Hz, but a 3-way with 10-12" bass you must play really loud to hear problems. The actual problem is spl vs distortion in the driver.

24bit or floating 32bit dynamic scale used in studios (or even most dsp processors) gives enormous scale to play with. "bass boost eq" shoud actually be attenuation of upper frequencies! Then there is no risk of clipping distortion with digital signal. The right speaker is resting on my desk to the right of a large monitor, effectively corner loaded by a wall behind the monitor and books on a bookcase.

ATC SUBWOOFER DRIVER

If I will go with a BR housing, I'd stick to ATCs specs and use a 10cm diameter and 20cm long tube which would put a 100L cabinet to a tuning frequency of circa 29Hz.ĭo you think that would work well or should I tune it even deeper to lets say 23Hz (Fs of the 12" ATC driver btw) AQ Type 4 10' (the older version with braided covers) ATC SCM 11 V2. Designed and produced in Denmark since 1983.)

ATC SUBWOOFER PRO

( Hiquphon 1st natural choice in 3/4" soft dome tweeters - 20mm soft dome tweeter type OWI, OWII, OW3, OW4. The ATC SCS70 Pro is a high-performance 12/300mm active subwoofer, designed from the ground upto deliver the exceptional levels ofperformance required to. There is also Hiquphon tweeters which are spoken to be brilliant. since I will be crossing over at 3.5kHz this would definitlely work.

ATC SUBWOOFER PROFESSIONAL

Coming from a professional studio monitoring background, PMC speakers are extremely neutral and natural. PMC specialise in transmission line speakers. Pete Thomas set up the company after leaving the BBC in 1990 and the Professional Monitor Company was born. such as: tighter/faster bass response, smoother roll-of and no port-noises.Īlso I am wondering if ported cabinets excite room modes quicker than sealed : another good point here I haven't totally forgotten about 3/4". MC Speakers are a British speaker manufacturer based in Luton. sealed boxes.īut fair enought to mention that sealed boxes have some advantages over ported cabinets too. They include a DSP too, so I can phase and time align drivers and adjust their frequency response if needed and adjust to my Darwin : Your points are fair regarding excursion and THD of ported vs. I will use those new Hypex Fusion plate amps once they are out in april. Thanks in : I forgot to mention but this build will be active either way. Well I guess bitumen and/or eggfoam to all plain surfaces, for sure.īut then should I also fill the whole void with wool?

ATC SUBWOOFER HOW TO

Since its a ported cabinet design I wouldn't know how to dampen the inside correctly. I really don't like ferrofluid tweeters as the ferrofluid can dry out over the years and change its frequency-response.įurther I was wondering if anybody here has seen a original ATC SCM100Asl from the inside. The T25CF001 however was originally used by ATC. The latter one has a waveguid and hence I expect better dispertion and I know this tweeter from Grimm and Kii Three speakers, which I both really like. I am torn between Seas T25CF001 (which ATC originally used in their line before they started making and using their own tweeters) I've got everything sorted except tweeters.